Subject / Started by | Replies / Views | Last post | |
---|---|---|---|
CNC Mill Conversion
Started by janz99 |
1 Replies
2910 Views |
April 22, 2016, 06:29:49 AM by Steve Stallings |
|
A-Axis Setup in Mach4
Started by ScottC |
1 Replies
3447 Views |
May 06, 2016, 01:24:30 AM by Bob at PMDX |
|
Getting Script to Run External Cycle Start
Started by ScottC |
1 Replies
3682 Views |
May 13, 2016, 04:36:18 PM by Bob at PMDX |
|
1 Replies
2877 Views |
May 16, 2016, 09:27:27 PM by Steve Stallings |
||
Starting from scratch
Started by iborg |
5 Replies
4175 Views |
July 28, 2016, 07:36:54 PM by Steve Stallings |
|
Basic information about set up.
Started by Bubbarice |
9 Replies
5686 Views |
August 11, 2016, 08:20:04 PM by Steve Stallings |
|
Stepper Motors & Driver Information
Started by Bubbarice |
2 Replies
3079 Views |
September 03, 2016, 08:43:44 PM by Steve Stallings |
|
PMDX Warranty -How Long?
Started by PWM |
3 Replies
3014 Views |
September 14, 2016, 09:08:28 PM by PWM |
|
1 Replies
2648 Views |
October 17, 2016, 08:02:47 PM by Steve Stallings |
||
2 Replies
2730 Views |
October 26, 2016, 08:27:02 PM by Steve Stallings |
||
MOVED: Problem with Spindle ON/OFF
Started by Bob at PMDX |
0 Replies
2648 Views |
October 31, 2016, 04:29:20 PM by Bob at PMDX |
|
How do configure my limit switches?
Started by racline98 |
2 Replies
2546 Views |
December 10, 2016, 05:36:48 PM by racline98 |
|
Help Initial Setup
Started by hooked |
11 Replies
4897 Views |
January 20, 2017, 10:01:15 PM by hooked |
|
Strange signals
Started by callcbm |
3 Replies
2782 Views |
January 23, 2017, 09:50:22 PM by Steve Stallings |
|
PMDX-416 PIN ALLOCATIONS
Started by hooked |
3 Replies
3476 Views |
February 05, 2017, 07:16:04 PM by Steve Stallings |
|
16 Replies
9032 Views |
February 13, 2017, 11:14:18 AM by Firechief |
||
touch plate support?
Started by crchisholm |
1 Replies
2786 Views |
February 28, 2017, 05:12:13 PM by Steve Stallings |
|
setting up limity switches and homing.
Started by crchisholm |
8 Replies
5965 Views |
March 15, 2017, 08:14:33 PM by crchisholm |
|
3 Replies
4296 Views |
March 16, 2017, 03:20:58 PM by crchisholm |
||
MOVED: CNC Router build...
Started by Steve Stallings |
0 Replies
2708 Views |
April 02, 2017, 06:13:39 PM by Steve Stallings |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic