| Subject / Started by | Replies  / Views |
Last post | |
|---|---|---|---|
|
Feed Rate & Spindle Speed Override Wiring?
Started by KG7AMV |
5 Replies
6055 Views |
July 21, 2015, 09:50:30 PMby Steve Stallings |
|
|
5 Replies
5492 Views |
July 07, 2015, 08:30:31 AM by Bob at PMDX |
|
|
|
5 Replies
3840 Views |
August 10, 2016, 12:19:10 PM by Steve Stallings |
|
|
|
Ports and Pins
Started by woodfish510 |
5 Replies
2566 Views |
April 25, 2019, 12:13:09 AM by 12strings |
|
|
Step Direction pin output.
Started by PaulC. |
5 Replies
4279 Views |
November 06, 2015, 05:04:07 PM by Steve Stallings |
|
|
5 Replies
3908 Views |
October 31, 2016, 10:59:50 PM by Bob at PMDX |
|
|
|
6 Replies
5119 Views |
October 06, 2017, 12:36:39 PM by NoellEagan |
|
|
|
PMDX-126 and ESS Relay Mist Problems
Started by Techsavvy34 |
6 Replies
5865 Views |
July 26, 2015, 03:57:48 AM by Techsavvy34 |
|
|
6 Replies
4416 Views |
October 13, 2016, 01:17:35 AM by Bob at PMDX |
|
|
|
Mach3 & PMDX 134
Started by olf20 |
6 Replies
3958 Views |
February 09, 2018, 06:18:18 PM by olf20 |
|
|
126-134 Motor #4 will not move
Started by Bill I |
6 Replies
3784 Views |
June 29, 2016, 08:20:40 PM by Bill I |
|
|
6 Replies
3776 Views |
November 08, 2016, 11:10:46 AM by timboberonion |
|
|
|
PMDX 126 & 108 - Spindle Encoder
Started by spumco |
6 Replies
5703 Views |
October 08, 2016, 10:20:09 PM by spumco |
|
|
PMDX-126 C, WITH 133, 3 GECKO 203V
Started by Futurepast |
6 Replies
4222 Views |
February 13, 2016, 09:31:15 PM by Bob at PMDX |
|
|
PMDX-126 Irratic power
Started by zkmiller |
6 Replies
5296 Views |
September 21, 2015, 06:02:36 PM by zkmiller |
|
|
6 Replies
4891 Views |
October 06, 2015, 04:08:26 PM by Bob at PMDX |
|
|
|
6 Replies
3560 Views |
September 03, 2016, 08:45:57 PM by Steve Stallings |
|
|
|
PDMX 1PARPCI 5 VOLT PARALLEL PORT CARD
Started by bwpigeon |
6 Replies
4413 Views |
March 15, 2017, 11:08:09 PM by Steve Stallings |
|
|
PMDX and clearpath in Test mode
Started by OldePhart |
7 Replies
3097 Views |
February 04, 2019, 09:45:39 PM by 12strings |
|
|
4th and 5th axis configuration with PMDX-126
Started by Max |
7 Replies
3173 Views |
March 31, 2019, 10:38:30 PM by 12strings |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic