Subject / Started by | Replies / Views | Last post | |
---|---|---|---|
1 Replies
3535 Views |
April 02, 2017, 07:02:27 PM by Steve Stallings |
||
Cannot activate Pins
Started by Daryl |
1 Replies
2349 Views |
March 26, 2016, 07:29:01 PM by Bob at PMDX |
|
PMDX expansion I/O survey
Started by Steve Stallings |
1 Replies
2921 Views |
November 06, 2016, 04:39:08 AM by Mike Abbott |
|
E stop on Smartbob424
Started by Terry Newlands |
1 Replies
2146 Views |
October 10, 2016, 04:42:26 PM by Steve Stallings |
|
1 Replies
4785 Views |
November 06, 2014, 04:55:20 PM by Bob at PMDX |
||
How much power is available on J9 +5volt
Started by gm276 |
1 Replies
3630 Views |
November 19, 2014, 11:53:34 AM by Steve Stallings |
|
PMDX 424 USB header shield ground
Started by Mike Abbott |
1 Replies
2624 Views |
August 29, 2016, 01:39:14 PM by Bob at PMDX |
|
PMDX 407 config save
Started by Mike Abbott |
1 Replies
2332 Views |
June 26, 2018, 02:33:18 AM by 12strings |
|
PMDX-411 and extension cables
Started by DstMkr |
1 Replies
2123 Views |
April 10, 2018, 09:45:20 PM by 12strings |
|
1 Replies
2248 Views |
July 29, 2017, 06:07:23 PM by mredski |
||
DRO from encoder input - PMDX-424
Started by beezerlm |
1 Replies
2396 Views |
August 12, 2016, 05:18:58 PM by Bob at PMDX |
|
G-code stops running with 411
Started by ScottC |
1 Replies
2417 Views |
August 29, 2016, 12:03:13 AM by Bob at PMDX |
|
Y-Axis (Motors 3A & #B) Not Turning
Started by bwolfe |
1 Replies
2204 Views |
August 11, 2018, 02:54:47 PM by bwolfe |
|
Mach4 pmdx 411 out of band spindle
Started by RhoTu |
1 Replies
1941 Views |
December 19, 2017, 11:36:52 PM by 12strings |
|
pmdx 422 step pulse width
Started by jcrowe |
1 Replies
3997 Views |
April 10, 2015, 05:45:57 PM by Bob at PMDX |
|
pmdx 410 threading
Started by wwenter |
1 Replies
2302 Views |
April 02, 2017, 06:22:35 PM by Steve Stallings |
|
PMDX-410 Pin Assignment Descriptions
Started by broered |
1 Replies
2875 Views |
May 11, 2015, 03:59:16 PM by Bob at PMDX |
|
1 Replies
2177 Views |
August 03, 2017, 11:32:16 PM by curt66140 |
||
Pmdx 414 into a chinese cnc controler
Started by Thomasm |
1 Replies
1968 Views |
April 22, 2018, 09:37:23 PM by Thomasm |
|
Intermitent startup
Started by RonGinger |
1 Replies
2850 Views |
July 27, 2015, 12:51:06 PM by Steve Stallings |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic