| Subject / Started by | Replies  / Views |
Last post | |
|---|---|---|---|
|
1 Replies
2716 Views |
May 29, 2017, 07:18:23 PMby Steve Stallings |
|
|
|
1 Replies
3643 Views |
April 02, 2017, 07:02:27 PM by Steve Stallings |
|
|
|
How to Set Common Signal to 5 volts
Started by ScottC |
1 Replies
2405 Views |
June 02, 2016, 11:51:14 AM by Bob at PMDX |
|
|
Stop button on mach4 and 424 board
Started by Kane17752 |
1 Replies
2257 Views |
May 29, 2017, 08:39:44 PM by Steve Stallings |
|
|
Sample PMDX-424 profile
Started by pedio |
1 Replies
2694 Views |
July 21, 2016, 02:54:25 PM by Bob at PMDX |
|
|
Mach4 pmdx 411 out of band spindle
Started by RhoTu |
1 Replies
2025 Views |
December 19, 2017, 11:36:52 PM by 12strings |
|
|
DRO from encoder input - PMDX-424
Started by beezerlm |
1 Replies
2501 Views |
August 12, 2016, 05:18:58 PM by Bob at PMDX |
|
|
G-code stops running with 411
Started by ScottC |
1 Replies
2521 Views |
August 29, 2016, 12:03:13 AM by Bob at PMDX |
|
|
PMDX 424 USB header shield ground
Started by Mike Abbott |
1 Replies
2728 Views |
August 29, 2016, 01:39:14 PM by Bob at PMDX |
|
|
PMDX 424 not detected
Started by Mike Abbott |
2 Replies
3732 Views |
December 04, 2016, 09:35:52 PM by Mike Abbott |
|
|
Error msg with PMDX 407 board
Started by Doddjn |
2 Replies
6124 Views |
January 25, 2015, 11:42:28 AM by Doddjn |
|
|
424, 407, Mach4 Lathe not homing
Started by Rad319 |
2 Replies
3897 Views |
December 09, 2016, 07:51:13 AM by Rad319 |
|
|
Z-axis Goto Zero not responding
Started by lebies |
2 Replies
5328 Views |
May 29, 2015, 02:47:45 PM by lebies |
|
|
PMDX-416 DROPS COMMS WITH MACH4
Started by hooked |
2 Replies
3099 Views |
February 19, 2017, 04:22:43 PM by Steve Stallings |
|
|
2 Replies
2810 Views |
November 03, 2015, 04:39:56 PM by Bob at PMDX |
|
|
|
SmartBob-411 & 126 K2 Relay
Started by shaddr3 |
2 Replies
3174 Views |
November 07, 2015, 12:34:22 AM by Bob at PMDX |
|
|
Rebuild Problem
Started by dq828 |
2 Replies
2266 Views |
February 21, 2018, 12:55:47 AM by 12strings |
|
|
2 Replies
2197 Views |
January 13, 2018, 11:32:09 PM by 12strings |
|
|
|
Laser on/off PMDX-422 Mach4
Started by WallClimber |
2 Replies
3860 Views |
January 25, 2016, 12:20:32 PM by WallClimber |
|
|
PMDX 424 and outputs
Started by Mike Abbott |
2 Replies
2712 Views |
July 26, 2016, 10:09:27 PM by Mike Abbott |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic