1
SmartBOB controllers and dedicated accessories / PMDX: DEVICE ERROR 'SYSTEM ERROR(18): Packet timeout, communications lost'
« on: October 27, 2019, 04:49:59 AM »
Hi there,
Me again. You replaced my PMDX 411 recently and it's been good as gold. I was running as a Mach4 3 axis router and although I haven't done any very big jobs, everything was running smoothly and as expected.
I recently added a fourth axis. I created a new profile on Mach4 using Mach4 mill. I copied most of the configuration settings across from the Mach4 Router profile and then played around getting the A axis revolving around X. After a bit of fine tuning I ran a few test cuts. everything seems OK except I get some weird crashes. Here is the history from the most recent few runs.
Any thoughts?
PMDX: Communication status 'Sync'd to Device'
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Current tool == Selected tool so there is nothing to do
Current tool == Selected tool so there is nothing to do
PMDX: DEVICE ERROR 'SYSTEM ERROR(18): Packet timeout, communications lost'
PMDX: Communication error 'Lost Sync'
PMDX: Communication status 'Sync'd to Device'
Home switch Z Home tripped!
Home switch X Home tripped!
PMDX: Error 7 (Communication error) queuing HOME pkt for axis 'Y' motor 'Master' (id 1), aborting HOME cmd
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Cycle Stopped
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Current tool == Selected tool so there is nothing to do
Cycle Stopped
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Current tool == Selected tool so there is nothing to do
Current tool == Selected tool so there is nothing to do
PMDX: Communication error 'Lost Sync'
PMDX: Communication status 'Sync'd to Device'
PMDX: DEVICE ERROR 'SYSTEM ERROR(18): Packet timeout, communications lost'
Cheers
Mark
Me again. You replaced my PMDX 411 recently and it's been good as gold. I was running as a Mach4 3 axis router and although I haven't done any very big jobs, everything was running smoothly and as expected.
I recently added a fourth axis. I created a new profile on Mach4 using Mach4 mill. I copied most of the configuration settings across from the Mach4 Router profile and then played around getting the A axis revolving around X. After a bit of fine tuning I ran a few test cuts. everything seems OK except I get some weird crashes. Here is the history from the most recent few runs.
Any thoughts?
PMDX: Communication status 'Sync'd to Device'
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Current tool == Selected tool so there is nothing to do
Current tool == Selected tool so there is nothing to do
PMDX: DEVICE ERROR 'SYSTEM ERROR(18): Packet timeout, communications lost'
PMDX: Communication error 'Lost Sync'
PMDX: Communication status 'Sync'd to Device'
Home switch Z Home tripped!
Home switch X Home tripped!
PMDX: Error 7 (Communication error) queuing HOME pkt for axis 'Y' motor 'Master' (id 1), aborting HOME cmd
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Cycle Stopped
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Current tool == Selected tool so there is nothing to do
Cycle Stopped
Home switch Z Home tripped!
Home switch X Home tripped!
Home switch Y Home tripped!
Current tool == Selected tool so there is nothing to do
Current tool == Selected tool so there is nothing to do
PMDX: Communication error 'Lost Sync'
PMDX: Communication status 'Sync'd to Device'
PMDX: DEVICE ERROR 'SYSTEM ERROR(18): Packet timeout, communications lost'
Cheers
Mark