Subject / Started by | Replies / Views | Last post | |
---|---|---|---|
Freezing during G code run
Started by JW |
9 Replies
6564 Views |
July 19, 2015, 02:09:00 AM by Steve Stallings |
|
7 Replies
6500 Views |
December 09, 2020, 04:22:28 PM by mckinleyrb |
||
VFD spindle controler noise
Started by bballish |
12 Replies
6398 Views |
March 27, 2016, 11:18:55 PM by bballish |
|
USB Cable Length - PMDX 422
Started by rae_gordon |
11 Replies
6364 Views |
November 14, 2015, 09:42:30 PM by Bob at PMDX |
|
Error msg with PMDX 407 board
Started by Doddjn |
2 Replies
6105 Views |
January 25, 2015, 11:42:28 AM by Doddjn |
|
4 Replies
5881 Views |
November 30, 2014, 09:35:36 PM by Steve Stallings |
||
14 Replies
5713 Views |
August 06, 2019, 12:19:04 AM by 12strings |
||
problem 422
Started by Blacksmith |
4 Replies
5515 Views |
March 08, 2015, 02:00:44 PM by Blacksmith |
|
23 Replies
5488 Views |
March 26, 2020, 10:10:57 PM by 12strings |
||
USB Pendant for Mach 4
Started by broered |
2 Replies
5488 Views |
October 24, 2015, 12:28:42 PM by broered |
|
7 Replies
5357 Views |
May 14, 2017, 09:05:05 PM by Steve Stallings |
||
Slaved Axis Homing - Issue
Started by JayTeague |
6 Replies
5356 Views |
March 24, 2015, 03:39:26 PM by Steve Stallings |
|
Problem with Spindle ON/OFF
Started by John Leyenaar |
8 Replies
5328 Views |
November 03, 2016, 10:28:57 AM by John Leyenaar |
|
Z-axis Goto Zero not responding
Started by lebies |
2 Replies
5304 Views |
May 29, 2015, 02:47:45 PM by lebies |
|
VistaCNC Pendant problem
Started by nmskies |
5 Replies
5265 Views |
February 16, 2016, 10:12:49 PM by Yomama |
|
3 Replies
5220 Views |
December 15, 2016, 09:59:29 PM by Bob at PMDX |
||
PMDX424 - Lathe threading - Mach4
Started by Tripp |
9 Replies
5157 Views |
February 25, 2021, 03:04:34 PM by spencyg |
|
PMDX-424 & DM556D WIRING
Started by beerus |
5 Replies
5049 Views |
February 14, 2016, 10:49:20 PM by Bob at PMDX |
|
0 Replies
5039 Views |
March 10, 2015, 10:03:14 AM by Bob at PMDX |
||
PNP Proximity Sensors
Started by rexx42 |
4 Replies
5003 Views |
March 28, 2015, 05:10:22 PM by rexx42 |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic