Parallel Port breakout boards, motherboards, and dedicated accessories

Pages: [1] 2 3 ... 10

Subject / Started by	Replies / Views	Last post
Welcome to Parallel Port breakout boards, motherboards, and accessory boards. Started by administrator	0 Replies 5101 Views	September 16, 2014, 02:34:47 PM by administrator
Outputs Enabled Light Started by tonyden	5 Replies 191 Views	April 07, 2023, 06:37:39 PM by Steve Stallings
PMDX-179-PAN Probe Triggered Light Always On Started by qahrens	3 Replies 1720 Views	April 03, 2023, 01:19:26 PM by Walter
Help configuring CNC/Mach3 with 2 pmdx-122 boards Started by kbaird62	0 Replies 78 Views	April 02, 2023, 07:08:34 PM by kbaird62
PMDX-126 and ESS Mapping Started by megaplow	2 Replies 911 Views	March 30, 2023, 02:44:08 PM by Walter
ROTARY AXIS SET UP Started by TOMMYD	0 Replies 88 Views	March 03, 2023, 07:17:04 PM by TOMMYD
107 Pin Options Started by courter	3 Replies 237 Views	January 14, 2023, 12:18:39 PM by courter
PMDX 126 J11 GND TO MACHINE Started by TOMMYD	1 Replies 250 Views	November 16, 2022, 10:24:09 AM by Steve Stallings
Trouble with using the pmdx-107 to control spindle with mach 3 Started by iwinchell9	4 Replies 352 Views	November 04, 2022, 11:47:18 AM by iwinchell9
TruCut CNC error ESS_v10rd1d Started by ciphersson	1 Replies 405 Views	August 25, 2022, 11:52:46 AM by Steve Stallings
PDMX 126 Rev A to Rev C upgrade Started by Trell88	1 Replies 675 Views	August 07, 2022, 08:42:08 PM by Steve Stallings
Max length for an e-stop run on the PMDX-126 Started by trebuchetguy	1 Replies 571 Views	August 07, 2022, 08:25:37 PM by Steve Stallings
PMDX-126 and probing trigger, error Started by keastab	1 Replies 412 Views	August 07, 2022, 08:23:04 PM by Steve Stallings
Can't get the spindle speed to match Mach4 commands Started by korbindallas	1 Replies 405 Views	August 07, 2022, 08:17:17 PM by Steve Stallings
PMDX-126, 107, ESS and Mach4 integration almost done Started by korbindallas	1 Replies 425 Views	July 26, 2022, 12:35:59 PM by korbindallas
PMDX 107 PMDX126 controlling VFD Huanyang HY03D023B not functioning with Mach3 Started by prestonengebretson@yahoo.	14 Replies 3737 Views	January 27, 2022, 02:16:42 PM by Uncle_Euge
PMDX-126 CNC Plasma Mach4. I need to bring in Analog or an ADC signal into mach Started by jbiberston	0 Replies 931 Views	August 11, 2021, 08:24:17 PM by jbiberston
PMDX 126 with PMDX 134 with Gecko 203V with Avis Stepper motors and Mach 4 Started by Xyetti	4 Replies 1343 Views	May 04, 2021, 06:01:28 AM by Xyetti
Incorrect voltage on PMDX-107 VSD interface Started by jrbloom	2 Replies 1170 Views	April 30, 2021, 12:21:27 PM by jrbloom
PMDX-126 Latching eStop Started by jrbloom	7 Replies 1681 Views	April 30, 2021, 10:53:30 AM by jrbloom

Pages: [1] 2 3 ... 10

Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)

Locked Topic
Sticky Topic