Subject / Started by | Replies / Views | Last post | |
---|---|---|---|
M3 and M4 control help
Started by andy_con |
1 Replies
4504 Views |
April 16, 2015, 07:51:51 PM by Steve Stallings |
|
M3 and M4 Turns Spindle CW???
Started by LerninCNC |
11 Replies
4243 Views |
December 24, 2017, 09:08:30 AM by LerninCNC |
|
Mach3 & PMDX 134
Started by olf20 |
6 Replies
3766 Views |
February 09, 2018, 06:18:18 PM by olf20 |
|
2 Replies
3450 Views |
August 02, 2015, 06:55:50 AM by CNCRouter4fun |
||
Mach4 and probing
Started by Mike Abbott |
1 Replies
4406 Views |
November 13, 2016, 10:55:03 PM by Bob at PMDX |
|
2 Replies
3277 Views |
February 20, 2016, 02:40:51 PM by Steve Stallings |
||
Machine Hold 126 REV C
Started by todd432 |
3 Replies
5174 Views |
January 09, 2015, 09:45:52 PM by Steve Stallings |
|
3 Replies
2411 Views |
June 02, 2017, 09:35:08 AM by kemlin |
||
1 Replies
1169 Views |
August 07, 2022, 08:25:37 PM by Steve Stallings |
||
Max output current
Started by wbirnie13@gmail.com |
3 Replies
2002 Views |
January 22, 2019, 12:45:16 AM by wbirnie13@gmail.com |
|
Model PMDX-2PARPCI
Started by CharlieM43 |
1 Replies
2275 Views |
March 31, 2016, 08:51:23 PM by Steve Stallings |
|
Motors Don't Move
Started by Aqsa Ali |
9 Replies
5456 Views |
July 05, 2016, 02:20:38 PM by Aqsa Ali |
|
MOVED: Cannot activate Pins
Started by Bob at PMDX |
0 Replies
2573 Views |
March 26, 2016, 07:29:13 PM by Bob at PMDX |
|
MOVED: E-Stop does not work
Started by Bob at PMDX |
0 Replies
2734 Views |
October 31, 2015, 12:10:25 AM by Bob at PMDX |
|
34 Replies
31903 Views |
August 14, 2015, 09:42:39 AM by Bob at PMDX |
||
7 Replies
3874 Views |
September 01, 2016, 05:09:19 AM by Alito |
||
New purchase (PMDX126) and No Power! Help
Started by usafsoc |
1 Replies
2049 Views |
November 29, 2017, 07:05:40 PM by Steve Stallings |
|
no power to G320X after sitting?
Started by kemlin |
1 Replies
1534 Views |
February 12, 2021, 09:40:57 AM by 12strings |
|
Outputs Enabled Light
Started by tonyden |
5 Replies
1057 Views |
April 07, 2023, 06:37:39 PM by Steve Stallings |
|
panasonic servo drives with pmdx126
Started by rbrintle |
3 Replies
4162 Views |
March 09, 2015, 11:11:35 PM by Steve Stallings |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic