| Subject / Started by | Replies / Views | Last post  |
|
|---|---|---|---|
|
Error 7 when attempting to Home
Started by WallClimber « 1 2 » |
16 Replies
24548 Views |
January 24, 2016, 11:01:08 PMby Bob at PMDX |
|
PMDX-422 - Signal names for J11 Pins
Started by broered |
1 Replies
6706 Views |
January 14, 2016, 06:57:55 PM by Steve Stallings |
|
|
Mach 4 Licensing thru PMDX
Started by HDVideo |
3 Replies
10095 Views |
January 04, 2016, 09:44:37 AM by HDVideo |
|
|
Limit switch recommendation
Started by John |
3 Replies
9218 Views |
January 02, 2016, 08:43:30 PM by Bob at PMDX |
|
|
Slaved axis problem
Started by bballish |
7 Replies
11969 Views |
December 20, 2015, 09:29:49 PM by Bob at PMDX |
|
|
1 Replies
6896 Views |
December 04, 2015, 12:11:02 AM by Bob at PMDX |
|
|
|
Spindle Issues with SuperPID
Started by Jarhead |
4 Replies
10462 Views |
November 24, 2015, 05:42:11 PM by Jarhead |
|
|
How to set up for Mach 4 to display RPM
Started by MitchB |
1 Replies
7636 Views |
November 21, 2015, 11:25:21 PM by Bob at PMDX |
|
|
USB Cable Length - PMDX 422
Started by rae_gordon |
11 Replies
13779 Views |
November 14, 2015, 09:42:30 PM by Bob at PMDX |
|
|
Setting up spindle PWM
Started by MitchB |
7 Replies
10206 Views |
November 07, 2015, 01:27:41 AM by Bob at PMDX |
|
|
SmartBob-411 & 126 K2 Relay
Started by shaddr3 |
2 Replies
7277 Views |
November 07, 2015, 12:34:22 AM by Bob at PMDX |
|
|
2 Replies
6990 Views |
November 03, 2015, 04:39:56 PM by Bob at PMDX |
|
|
|
mach 4 dro is moving but motors are not
Started by bballish |
13 Replies
14458 Views |
November 02, 2015, 02:18:01 PM by Bob at PMDX |
|
|
1 Replies
7143 Views |
October 30, 2015, 10:40:52 PM by Steve Stallings |
|
|
|
E-Stop does not work
Started by madiaz91911 |
1 Replies
6934 Views |
October 30, 2015, 04:35:17 PM by Steve Stallings |
|
|
1 Replies
7170 Views |
October 29, 2015, 01:04:20 AM by Bob at PMDX |
|
|
|
USB Pendant for Mach 4
Started by broered |
2 Replies
9681 Views |
October 24, 2015, 12:28:42 PM by broered |
|
|
Ethernet smart bob
Started by matt1911 |
6 Replies
12054 Views |
October 05, 2015, 07:34:06 PM by Steve Stallings |
|
|
6 Replies
9909 Views |
October 01, 2015, 09:04:35 PM by Bob at PMDX |
|
|
|
Slave axis homing
Started by pedio |
3 Replies
9025 Views |
September 25, 2015, 11:47:13 PM by Bob at PMDX |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic