Subject / Started by | Replies / Views | Last post | |
---|---|---|---|
Planning cnc plasma controller?
Started by Brad k |
1 Replies
3359 Views |
April 18, 2017, 08:42:44 PM by Steve Stallings |
|
PMDX-422 - Signal names for J11 Pins
Started by broered |
1 Replies
2370 Views |
January 14, 2016, 06:57:55 PM by Steve Stallings |
|
PMDX-424 driving Gecko G214
Started by broered |
3 Replies
3710 Views |
December 19, 2016, 02:12:15 AM by Bob at PMDX |
|
PMDX-422 - External +5V Power Supply
Started by broered |
3 Replies
2933 Views |
March 31, 2016, 07:24:30 PM by Steve Stallings |
|
PMDX-424 Tandem Motor Configuration
Started by broered |
6 Replies
3983 Views |
April 12, 2016, 08:22:30 PM by broered |
|
USB Pendant for Mach 4
Started by broered |
2 Replies
5261 Views |
October 24, 2015, 12:28:42 PM by broered |
|
2 Replies
3239 Views |
April 25, 2016, 11:04:51 AM by broered |
||
PMDX-410 Pin Assignment Descriptions
Started by broered |
1 Replies
2726 Views |
May 11, 2015, 03:59:16 PM by Bob at PMDX |
|
3 Replies
3406 Views |
October 27, 2017, 05:03:39 AM by MikekiM |
||
Wiring E-Stop to PMDX-424
Started by bwolfe |
2 Replies
2160 Views |
July 08, 2018, 03:42:57 PM by bwolfe |
|
Y-Axis (Motors 3A & #B) Not Turning
Started by bwolfe |
1 Replies
1911 Views |
August 11, 2018, 02:54:47 PM by bwolfe |
|
3 Replies
2267 Views |
July 26, 2018, 08:51:14 AM by bwolfe |
||
3 Replies
3132 Views |
June 28, 2018, 11:14:30 PM by webdevl |
||
PMDX-411 not powering up
Started by c12kipp |
4 Replies
2197 Views |
January 14, 2018, 05:33:43 AM by c12kipp |
|
Newbie growing pains PMDX422
Started by Charlie |
14 Replies
9747 Views |
January 29, 2015, 09:55:57 PM by Bob at PMDX |
|
2 Replies
1995 Views |
January 13, 2018, 11:32:09 PM by 12strings |
||
2 Replies
1751 Views |
November 11, 2020, 05:47:37 PM by Chuckb67@live.com |
||
PMDX-424 Power Not Coming On
Started by CNCRick |
4 Replies
2327 Views |
February 18, 2017, 07:39:48 PM by CNCRick |
|
PMDX-424 to DQ860MA Wiring Setup
Started by CNCRick |
2 Replies
2868 Views |
February 19, 2017, 04:04:47 PM by Steve Stallings |
|
3 Replies
3466 Views |
May 14, 2017, 09:03:31 PM by Steve Stallings |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic