| Subject / Started by | Replies / Views | Last post  |
|
|---|---|---|---|
|
PMDX-416 DROPS COMMS WITH MACH4
Started by hooked |
2 Replies
16233 Views |
February 19, 2017, 04:22:43 PMby Steve Stallings |
|
|
PMDX-424 to DQ860MA Wiring Setup
Started by CNCRick |
2 Replies
16080 Views |
February 19, 2017, 04:04:47 PM by Steve Stallings |
|
|
1 Replies
13810 Views |
February 19, 2017, 04:02:14 PM by Steve Stallings |
|
|
|
PMDX-424 Power Not Coming On
Started by CNCRick |
4 Replies
17442 Views |
February 18, 2017, 07:39:48 PM by CNCRick |
|
|
4 Replies
19612 Views |
February 01, 2017, 08:35:33 AM by Michael Arnold |
|
|
|
Stepper Motor Config
Started by mntlvr |
4 Replies
19421 Views |
January 23, 2017, 05:37:42 PM by Steve Stallings |
|
|
Connecting 407 to new VFD
Started by Almasts |
5 Replies
22088 Views |
January 22, 2017, 08:36:05 PM by Almasts |
|
|
Homing - 0.050" Move
Started by beezerlm |
13 Replies
31189 Views |
January 04, 2017, 05:20:21 PM by Steve Stallings |
|
|
7 Replies
23281 Views |
January 01, 2017, 10:53:33 AM by racline98 |
|
|
|
PMDX-424 vs PMDX-416
Started by Rubes |
3 Replies
20939 Views |
December 22, 2016, 07:32:28 PM by Steve Stallings |
|
|
PMDX-424 driving Gecko G214
Started by broered |
3 Replies
20805 Views |
December 19, 2016, 02:12:15 AM by Bob at PMDX |
|
|
3 Replies
22834 Views |
December 15, 2016, 09:59:29 PM by Bob at PMDX |
|
|
|
424, 407, Mach4 Lathe not homing
Started by Rad319 |
2 Replies
18162 Views |
December 09, 2016, 07:51:13 AM by Rad319 |
|
|
PMDX 424 not detected
Started by Mike Abbott |
2 Replies
19731 Views |
December 04, 2016, 09:35:52 PM by Mike Abbott |
|
|
PMDX-424 ClearPath Motor Configeration
Started by dq828 |
2 Replies
16489 Views |
November 11, 2016, 05:14:30 AM by dq828 |
|
|
PMDX expansion I/O survey
Started by Steve Stallings |
1 Replies
15053 Views |
November 06, 2016, 04:39:08 AM by Mike Abbott |
|
|
Problem with Spindle ON/OFF
Started by John Leyenaar |
8 Replies
25637 Views |
November 03, 2016, 10:28:57 AM by John Leyenaar |
|
|
pmdx 424 and pmdx 407 speed control
Started by Mike Abbott |
3 Replies
26278 Views |
October 31, 2016, 10:58:07 PM by Bob at PMDX |
|
|
PMDX-424 and KL-6050 Driver Pinout
Started by Satmanager |
4 Replies
18296 Views |
October 21, 2016, 02:10:13 AM by Satmanager |
|
|
E stop on Smartbob424
Started by Terry Newlands |
1 Replies
15567 Views |
October 10, 2016, 04:42:26 PM by Steve Stallings |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic