Providing
Electronic
Solutions
Since 1984
an affiliate of Practical Micro Design, Inc.
Products for CNC and motion control applications
General Information
FIND PRODUCTS:
Select Below
To Browse
- Listed by Number (All)
- PMDX-340 CNC Controller
- Breakout Boards
- Extra I/O & Isolation
- Motherboards
- Gecko Drivers
- Heatsinks
- Power Sources
- Test & Development Tools
- Spindle Controllers
- Panels, Pendants & MPGs
- Sensors & Home/Limit Switches
- Contactors, Breakers,
SSRs, Power Switches,
& Power Line Filters - E-Stop & Control Switches
- Cables & Parallel Ports
- Connectors, Wires & Misc
- Legacy Products
Our Most Popular Products
Listing of all our products in numerical order
If the item you are looking for is not in the list above, it may be on our Legacy Products page.
| PMDX-103 | Parallel Port Isolator Board |
| PMDX-104 | 4-Channel Relay Output Board |
| PMDX-105 | Quad Isolator Board |
| PMDX-106 | Spindle Control Interface (with and without operator panel controls) |
| PMDX-107 | Isolated Speed Control |
| PMDX-108-Input | 8-Channel Isolated Input Board for parallel port pins 2-9 |
| PMDX-108-Output | 8-Channel Isolated Output Board for parallel port pins 2-9 |
| PMDX-109 | 8-Channel Relay Board (5V or 24V version) |
| PMDX-111 | Parallel Port Monitor |
| PMDX-112 | Parallel Port Electrical Simulator and Tester (available with a small stepper motor or small stepper motor and small servo motor) |
| PMDX-120 | Parallel Port Accessory Module |
| PMDX-122 | Bi-Directional Breakout Board |
| PMDX-125 | Multi-Mode Breakout Board Replaced by PMDX-126 |
| PMDX-126 | Multi-Mode Breakout Board |
| PMDX-132 | Breakout/Motherboard Combo for Geckos |
| PMDX-133 | 3-Axis Daisy-Chainable Motherboard for Geckodrive G201X and G203V Stepper Motor Drivers |
| PMDX-134 | Simple Motherboard for Geckodrive G201X and G203V Stepper Motor Drivers |
| PMDX-135 | Power Prep Module (50V,20A or 80V,20A) |
| PMDX-136 | Power Prep Module, 50V, 10A |
| PMDX-145 | Pendant Adapter Board |
| PMDX-170 | Slotted Optical Sensor |
| PMDX-171 | Hall Effect Sensor |
| PMDX-179 | Remote Status Indicator Board |
| PMDX-340 | PMDX-340 CNC Machine Controller |
| PMDX-3Pin-PlugAndJack | 3-Pin Plug and Jack Set with Shield |
| PMDX-4Pin-PlugAndJack | 4-Pin Plug and Jack Set with Shield |
| PMDX-5Pin-PlugAndJack | 5-Pin Plug and Jack Set with Shield |
| PMDX-6Pin-PlugAndJack | 6-Pin Plug and Jack Set with Shield |
| PMDX-8Pin-PlugAndJack | 8-Pin Plug and Jack Set with Shield |
| PMDX-CAT5-7S | Cat5 Shielded Ethernet Cable, 7 foot |
| PMDX-CENtoDB25M | Centronics to DB-25 Male 6 Foot External Cable |
| PMDX-Contactor18-120 | 18 Ampere Power Contactor/Motor Starter, 120VAC Coil |
| PMDX-Contactor18-230 | 18 Ampere Power Contactor/Motor Starter, 230VAC Coil |
| PMDX-DB25MtoM | DB-25 Male to Male 6 Foot External Cable |
| PMDX-DB25Ribbon | DB-25 Female to 26-pin Ribbon Cable Plug Connector, 6 inch |
| PMDX-DB25Ribbon-18 | DB-25 Female to 26-pin Ribbon Cable Plug Connector, 18 inch |
| PMDX-EStop-Mini | 16mm Miniture Emergency Stop Switch |
| PMDX-EStop-Std | 22mm Standard Size Emergency Stop Switch |
| PMDX-EStop-Std2NC | 22mm Standard Size Emergency Stop Switch with 2 N/C Contacts |
| PMDX-HRD10Ribbon | 10-pin Female to Female Ribbon Header Cable |
| PMDX-HRD26Ribbon | 26-pin Female to Female Ribbon Header Cable, 6 inch |
| PMDX-HRD26Ribbon-18 | 26-pin Female to Female Ribbon Header Cable, 18 inch |
| PMDX-Heatsink-01 | Heatsink for 4 Gecko drivers and a bridge rectifier |
| PMDX-Limit-Std | Standard Size Mechanical Microswitch for Limits |
| PMDX-LineFilter-20D | Dual-stage Line Filter for AC Mains Power |
| PMDX-MPG-01 | Manual Pulse Generator |
| PMDX-Prox-01 | Rectangular Normally-Open NPN-style Proximity Sensor |
| PMDX-SSR25 | Solid-State Relay, 25A, 250VAC |
| G203V | Geckodrive G203V Stepper Motor Driver |
| G320X | Geckodrive G320X Brush DC Servo Motor Driver |
If the item you are looking for is not in the list above, it may be on our Legacy Products page.
Copyright 2004-2013 Practical Micro Design, Inc.